These use heavy duty 3″ square tubing. They are welded sturdy with all external welds cleaned and smoothed.

The top is a 4″ piece of flat bar with pre-drilled holes to easily mount your table top. Simply use wood screws or lag bolts into your favourite wood top to finish (hardware not included).

Different size tubing can be used on request. I’d be happy to work with you on all custom requests, so contact me to get the conversation going!

How to choose your size:

Generally the table top should overhang the legs by at least a couple of inches on either side, and more as the table width increases. This recommended amount of overhang will be reduced for benches which require maximum stability. For example, if you’re  table top is 24″ wide, then you’ll probably want a table leg 18~20″ wide.

I offer these legs painted in flat black, or in raw steel straight from the shop. If you’re looking for a custom colour, just send me a note and I will do my best to accomodate.

The post X Shaped Table Legs (3 inch) appeared first on Fabrications by Steve.

Each cable run uses 1/8″ stainless steel aircraft cable. All cable fittings are also stainless steel, making this a perfect indoor or outdoor solution.

The post Cable Railing appeared first on Fabrications by Steve.

These are great stoves for camping or if your location will not allow an open firepit in the backyard.

Top supports a pot or pan for cooking.

These designs are super efficient. Just load the middle with sticks, put a little paper in the bottom and light it up! Air gets sucked in through the bottom and flames come out the top.

The post Rocket Stove appeared first on Fabrications by Steve.

These use heavy duty 2″ square tubing. They are welded sturdy with all external welds cleaned and smoothed.

The top is a 4″ piece of flat bar with pre-drilled holes to easily mount your table top. Simply use wood screws or lag bolts into your favourite wood top to finish (hardware not included).

Different size tubing can be used on request. I’d be happy to work with you on all custom requests, so contact me to get the conversation going!

How to choose your size:

Generally the table top should overhang the legs by at least a couple of inches on either side, and more as the table width increases. This recommended amount of overhang will be reduced for benches which require maximum stability. For example, if you’re  table top is 24″ wide, then you’ll probably want a table leg 18~20″ wide.

I offer these legs painted in flat black, or in raw steel straight from the shop. If you’re looking for a custom colour, just send me a note and I will do my best to accomodate.

The post X Shaped Table Legs (2 inch) appeared first on Fabrications by Steve.

These use heavy duty 3″ square tubing. They are welded sturdy with all external welds cleaned and smoothed out.

The top is a 4″ piece of flat bar with pre-drilled holes to easily mount your table top. Simply use #8-#12 screws into your favourite wood top to finish (hardware not included).

The order is for a set of 2 legs.

Different size tubing can be used on request. I’d be happy to work with you on custom sizes, so if there is something specific that is not listed here please contact me.

How to choose your size:

Generally the table top should overhang the legs by at least a couple of inches on either side, and more as the table width increases. This recommended amount of overhang will be reduced for benches which require maximum stability. For example, if you’re  table top is 24″ wide, then you’ll probably want a table leg 18~20″ wide.

I offer these legs painted in flat black, or in raw steel straight from the shop. If you’re looking for a custom colour, just send me a note and I will do my best to accomodate.

The post U Shaped Table Legs (3-inch) appeared first on Fabrications by Steve.

Built with Canadian made 1.5″ square steel tubing. The ends are capped with flat bar and cleaned so that no fingers or clothing get caught.

The wall mounts extend the handrail 2″ from the wall. They are afixed to a 3″ piece of flat bar with 4 screw holes for mounting.

The wall mounts are 6″ in from the edges. For handrails over 6′ long an additional wall mount support is added.

These are made to custom order so any of the dimensions can easily be adjusted. Send me a message and we can get it exactly how you want it.

The post Handrail appeared first on Fabrications by Steve.

These use heavy duty 2″ square tubing. They are welded sturdy with all external welds cleaned and smoothed.

The top is a 4″ piece of flat bar with pre-drilled holes to easily mount your table top. Simply use #8 – #12 screws into your favourite wood top to finish (hardware not included).

The order is for a set of 2 legs.

Different size tubing can be used on request. I’d be happy to work with you on custom sizes, so if there is something specific that is not listed here please contact me.

How to choose your size:

Generally the table top should overhang the legs by at least a couple of inches on either side, and more as the table width increases. This recommended amount of overhang will be reduced for benches which require maximum stability. For example, if you’re  table top is 24″ wide, then you’ll probably want a table leg 18~20″ wide.

I offer these legs painted in flat black, or in raw steel straight from the shop. If you’re looking for a custom colour, just send me a note and I will do my best to accomodate.

The post U Shaped Table Legs (2-inch) appeared first on Fabrications by Steve.